It comes up and off and then the harness just has a tab on it. I'm just prying with a small screwdriver to release those clips. You can see how you try to use the clip tool or a screwdriver to pry the clip out. In this video, we're going to show you how to replace the rear outside door handles on this 2007 Denali. Im talking half off or more in some instances. Easy Returns Guaranteed We offer a no-questions 100% money back guarantee on all items returned within 60 days of delivery.
We'll speed up here as I just remove those three 7mm bolts. Then put the two 7mm bolts that hold it and tighten them up. Once you have everything lined up, then you can reset the clips. When you tighten these, tighten them up firm, you don't want to tighten them, though, and make sure you have the harness pulled up through, put the two trim pieces in place. Just pry lightly between the handle and the top of the door panel and push out at the same time to release the door handle. Then there's a couple clips at the top. If not, remove that, then the switch pulls right out.
Once you get the center up, you just kind of work it into the front, and then work it into the rear. In some cases the manufacturer does not allow us to show you our lower prices until you take further action. I'll fast forward as I do that. I had looked other places online and in store and they were by far the most reasonable. Also check out our other helpful how-to and diagnosis videos.
We hope this video helped you out. Again, you'll have to do this probably three or four times if your door panel has never been off before. What Go-Parts Guarantees You: Lifetime Warranty Guaranteed Every part comes with a limited lifetime warranty. Loosen that 10mm nut and pull the battery cable up and off, and then put it to the side so it won't contact the terminal again. Then you can work your hand underneath and release the rest of the clips.
. You kind of pry up in the center and then you pull it up and it locks. You press the tab and unplug it. If you find a product sold for a lower price by another vendor, we will beat or match their price. Here's a better shot of them as they come out. To reinstall the door panel, get it close, put the ball of the cable into the door handle, then pull the cable around and clip it in. There's probably three or four of these little black clips.
Use a plastic trim tool or a rag and a flat blade screwdriver, and pry up on the switch panel. Two of them hold the handle to the door panel. There are three 7mm bolts to remove on the backside of the handle. And another important factor is the price was right. Again, just tighten them firm. You pull it out and up out of the handle, and then the door panel comes right off.
You want to get it nice and firm, but you don't want to over-tighten it and strip the plastic threads. Fast Shipping Guaranteed Most orders are shipped out the same day as they're received. We already removed the 7mm bolt that holds the switch into the handle. Move the panel close to the door, make sure that the harness comes up through, and then make sure that the door lock goes up through the hole there, and then you kind of lift the panel up and push the top on and set it down into that window ledge clip, and then you can kind of look in behind, make sure that the clips line up. Correct Item Guaranteed If you receive an incorrect item from us, we will immediately pay for return shipment and send you the correct item.
As a retailer, we set our own prices independently, but some manufacturers restrict how we may communicate those prices. I was able to choose the mirror I needed with no problems for my 2003 mercury mountaineer. One of them holds the switch to the handle. If your door panel has never been off before, the water shield, the white water shield you can see is a black clip holding it to the door panel. Then it snaps into place.
Item in Good Condition Guaranteed If the part we ship to you arrives in damaged or non-working condition, we will ship another item out to you immediately. Set that, make sure you leave it unlocked, and then reinstall the two 10mm bolts that hold the panel in place. Use a rag to protect your paint and a door panel clip tool, or you could use a putty knife, but you work either the tool or the knife in underneath the clip. Best Price Guaranteed Our prices are hands-down some of the lowest you'll find on the net. Put the negative battery cable back on the post and 10mm socket, ratchet, and extension, then tighten it up. Eventually, I just end up grabbing ahold of the clip and the water shield at the same time and pull them out.
We'll need to undo the door handle cable clip. Then there is also a little panel underneath here that you pry out. Be careful not to over-tighten. New handle, put the switch back into place and then put that 7mm bolt that holds it, goes at the top of the switch on the backside, then tighten that up. Then pull the door handle out. Make sure that you pull the lock knob up and then put the lock trim on there.